Skip to main content
Version: 0.13.0

Appendix B: CPR Hardware

When using a Clearpath Robotics UGV and Base Station, the following hardware setup may be required.

Calibrating the IMU​

Although IMU magnetometers are calibrated at the factory to remove any internal magnetic influences in the device, measurements are still subject to influence from external magnetic anomalies when the sensor is installed. These anomalies are divided into two classes: hard iron offsets and soft iron distortions. Hard iron offsets are created by objects that produce a magnetic field. Soft iron distortions are considered deflections or alterations in the existing magnetic field. Ideally, these influences are mitigated by installing the sensor away from magnetic sources, such as coils, magnets, and ferrous metal structures and mounting hardware. However, often these sources are hard to avoid or are hidden. To mitigate this effect when using the IMU magnetometer to aid in heading estimations, a field calibration of the magnetometer after final installation is highly recommended. This means that the IMU must be calibrated in the same environment that you use your UGV for autonomous navigation.

Microstrain IMU​

If your UGV has a 3DM-GX5-25 Microstrain IMU, the complete instruction on calibration of your IMU can be found in section 5.4 of the datasheet. Note that you need a computer with Windows system and the LORD Sensing MIP Hard and Soft Iron Calibration software installed which can be found at the Microstrain website.

UM6/7 IMU​

If you are using UM6 or UM7 IMUs, you will need the magnetometer display package which is located at the following address on your UGV: ~/catkin_ws/Drivers/src/imu_tools/magnetometer_display.

Follow these steps to calibrate the IMU on your machine:

  1. Create a catkin workspace on your local machine and copy the package magnetometer_display into your src folder. Build this package with the catkin_make command.

  2. Perform the following command to make the calibration script executable:

    $ sudo chmod +x calibration.py

  3. Connect the IMU to your computer and launch the driver. Or if you are on the same network as your UGV, make your UGV the ROS master and ensure that you can echo the IMU topic on your computer.

  4. Open the magnetometer.launch file in the magnetometer_display package and change the sections shown in the figure below. Specifically, set use_mag_field to true when the IMU is outputting magnetometer measurements with a sensor_msgs/MagneticField message, otherwise set to false. Microstrain is the only IMU which uses the MagneticField message type.

    Magnetometer calibration, general launch settings

  5. Launch the calibration using the following command:

    $ roslaunch magnetometer_display magnetometer.launch

  6. Move the IMU around to get good coverage. RViz will display magnetometer points (red) and will plot current ellipsoid fit (green) as shown in the figure below.

    Magnetometer calibration, ellipsoid fit plot

  7. Ellipsoid fit parameters are displayed in terminal as shown in the figure below.

    Magnetometer calibration, ellipsoid fit parameters

  8. Once there are enough red points on your fitted ellipsoid, enter the above calibrations in the IMU driver launch file. Open the sensor.launch file in the cpr_gps_localization package and go to the UM7 (or UM6) section of the launch file. The figure below shows this section for the UM7.

    Magnetometer calibration, ellipsoid fit settings in launch file

    You should enter the parameters generated in the Ellipsoid fit step as follows (to account for the NED to ENU transform the driver applies):

    • Launch file X = Terminal Y
    • Launch file Y = Terminal X
    • Launch file Z = -Terminal Z

RTK Positioning GPS Setup​

note

Please skip this section if your robot does not have RTK GPS.

The following configuration is for establishing communications between the Base Station and the UGV using TCP/IP for the purpose of transmitting RTK corrections. Before starting this procedure, make sure that you have installed the SwiftNav console.

Base Station GPS Configuration​

  • Connect the Swift Navigation device to a computer via USB or the USB to Serial Adapter cable.

  • Open Swift Console and connect to the device.

  • Set the following options in the ethernet section as shown in the figure below.

    1. ip_config_mode: Static
    2. ip_address: 192.168.131.30
    3. netmask: 255.255.255.0
    Base Station Ethernet settings

  • Set the following options in the tcp_server1 section as show in the figure below.

    1. mode: SBP
    2. port: 55556
    3. enabled_sbp_messages: 72,74,117,65535
    Base Station TCP1 Server settings

  • Set the following options in the solution section as shown in the figure below.

    1. soln_freq: 10
    2. correction_age_max: 30
    3. output_every_n_obs: 10
    4. dgnss_solution_mode: Low Latency
    Base Station Solution settings

  • Next the Base Station has to be surveyed. There are two ways of doing this which are explained in RTK Survey Positioning.

  • Click Save to Flash.

  • Close Swift Console.

  • Disconnect the device from the computer.

UGV Position GPS Configuration​

  • Connect the Swift Navigation device to a computer via USB or the USB to Serial Adapter cable.

  • Open Swift Console and connect to the device.

  • Set the following options in the ethernet section as shown in the figure below.

    1. ip_config_mode: Static
    2. ip_address: 192.168.131.31
    3. netmask: 255.255.255.0
    UGV GPS Ethernet settings

  • Set the following options in the tcp_client0 section as show in the figure below.

    1. mode: SBP
    2. port: 192.168.131.30:55556
    3. enabled_sbp_messages: 0
    UGV GPS TCP Client0 settings

  • Set the following options in the solution section as show in the figure below.

    1. soln_freq: 10
    2. correction_age_max: 30
    3. output_every_n_obs: 10
    4. dgnss_solution_mode: Low Latency
    UGV GPS Solution settings

  • Click Save to Flash.

  • Close Swift Console.

  • Disconnect the device from the computer.

Once you have entered these settings. Connect your computer to the Wi-Fi network of the Base Station. Also make sure that the UGC (which is connected to the UGV GPS unit) is also connected to the Base Station Wifi. The you should be able to verify connectivity across the devices. To check the Base Station, complete the following steps.

  • Open Swift Console on you computer
  • Select TCP/IP
  • For IP Address enter 192.168.131.30
  • For IP Port enter 55555
  • Click OK
  • Select the Observations tab
  • In the Remote section you should see observation data from your UGV.

To check the UGV, complete the following steps.

  • Open Swift Console
  • Select TCP/IP
  • For IP Address enter 192.168.131.31
  • For IP Port enter 55555
  • Click OK
  • Select the Observations tab
  • In the Remote section you should see observation data from your Base Station.

Further information on RTK setup is available from SwiftNav.

RTK Survey Positioning​

note

Please skip this section if your UGV does not have RTK GPS.

danger

Once you have surveyed the location of the Base Station, you cannot relocate the Base Station throughout your tests. Otherwise, this step has to be repeated.

There are three ways to survey the Base Station location:

  1. OutdoorNav Web User Interface (easiest/accurate),
  2. Swiftnav console autosurvey (fastest/least accurate),
  3. ROS launch file geodetic survey (for debug output display).

Using the OutdoorNav Web UI is the easiest and most accurate way to do this since it runs the ROS geodetic survey tool which uses more samples to compute the final position of the Base Station than the Swiftnav console. Using the geodetic ROS survey launch file directly would allow the user to visualize the output log directly but requires preliminary knowledge in ROS.

Base Station Survey: Web UI​

Using the OutdoorNav Web UI to survey the Base Station is very simple. See Survey Base Station for details.

Base Station Survey: Piksi Console​

Use the Piksi console connect the base station GPS. Go to "Settings -> surveyed position", click to any field in this section and then click the button on the top right corner "Auto Survey". The figure below shows these steps. The last 1000 GPS points will be used to compute the position of the Base Station.

Auto Survey

After that, make sure the four fields in "surveyed position" (broadcast, surveyed lat, surveyed lon, surveyed alt) are consistent with your location.

Base Station Survey: ROS Geodetic Survey​

The ethz_piksi_ros repository should be installed in the UGV's catkin_ws. To run the surveying process simply connect your PC to the Base Station network, ssh into the UGV's computer and run the following:

roslaunch {robot_name}_gps_navigation geodetic_survey.launch

where robot_name is either jackal, husky, or warthog depending on your UGV. The surveying will begin and you will see a running tally of the collected data.

RTK Heading Setup​

For the rest of this section, it is assumed that a third Swiftnav Duro device is available with IP address of 192.168.131.32. Note that in order to change the IP address of a Swiftnav Duro, you need to use the Swiftnav console and connect to the device with the serial port.

note

The instructions in this section will overwrite some of the settings set in UGV Position GPS Configuration on the Position/Reference Duro receiver. This is normal since the configuration in UGV Position GPS Configuration is for a UGV with only the position Duro receiver. If the heading receiver is connected as well, please continue with the instructions below.

The two Swiftnav Duro GPS device on the UGV are connected via serial cable. They are also both connected via Ethernet cable to the computer on the UGV. For computing the heading, on Duro (the one on the rear with IP address 192.168.131.31) operates only to provide GNSS Observations to the other Duro that computes an RTK derived heading (the Duro on the front with IP address 192.168.131.32). For the purposes of this document, we will call the Duro/Piksi that operates to provide the raw GNSS observations only the "Reference Receiver" and the Duro/Piksi producing heading measurements the "Attitude Receiver."

Use the Swiftnav console to connect to the Reference Receiver (with IP address of 192.168.131.31) and insert the settings shown in the figure below.

Reference Receiver settings

Next, connect to the Attitude Receiver (with IP address of 192.168.131.32) and change the configuration as shown in the figure below.

Attitude Receiver settings

For further information please refer to these instructions.

Wireless Motion Stop​

Please refer to the hardware user manual of the motion stop device for proper usage. A trained operator should be used to supervise navigation of the UGV under autonomous control at all times. The Operator should be familiar with the use of the wireless motion stop device.

Last updated on